WiFi definition
WiFi technology (IEEE802.11) can be broadly categorised to IEEE802.11 a/b/g/n/ac. Each is an improvement in transmission speed and/or signal range from the previous, although these days only ‘G’ and ‘N’ are used.
The standard G versions of networking devices have an optimal transmission speed of 54 Mbps with an indoor range of approximately 40 m whereas the N versions have a theoretical maximum speed of 300 Mbps (practical of approximately 150 Mbps and above) with an indoor range in the region of 70 m.
In addition to this, N variations offer the choice of two frequency ranges; 2.4 GHz or 5 GHz. The higher frequency has no impact on the range but offers a potentially less polluted frequency to help reduce crosstalk noise.
Both the G and the N devices utilise the same channel capabilities but these vary regionally. In Europe (including UK) a channel system of 1-13 is used whereas in the US the system uses 1-11. Both use the same frequency ranges resulting in an approximate frequency void of 16.5 MHz at the end of the 2.4 GHz range.
Japan utilise a different system still, expanding the 2.4 GHz range beyond the acceptable ISM guidelines by 10.5 MHz to allow for an additional 14th channel with 11 MHz of non-interference from other channels (see Figure below) [80], [81], [82].
Image. 22MHz channel allocations for WiFi 2.4GHz frequencies, with curvatures implying affinities for intra-channel frequency selection.
The figure above shows the affinities for the frequency selection within each 22 MHz channel and the overlap between channel frequencies. The same would be seen for 40 MHz channels with the obvious exception that there would be twice the amount of overlap between channels, leaving fewer isolated channels. The solid lines show the 3 channels in the US 11 channel system that do not encroach on each other’s range at all. Each WiFi access point will secure its own channel and use that channel for all communications. Multiple channels will not be utilised by one access point other than during overlap.
WiFi communication protocols are Internet Protocol (IP) based where the destination address is in packet headers allowing large amounts of data to be transmitted through a network of nodes at high speed. This means that on any WiFi network a central control node (network coordinator) will allocate all IP’s in the network on discovery allowing for any packets to be addressed and routed to a connected device [82].
This article was created by --BRE. It was taken from The future of electricity in domestic buildings, a review, by Andrew Williams, published in November 2014.
NB The term 'WiFi' was coined by the Wi-Fi Alliance as shorthand for wireless local area network (WLAN) products based on the Institute of Electrical and Electronics Engineers' (IEEE) 802.11 standards. It did not specifically 'stand for' anything. It has popularly been adopted to mean Wireless Fidelity but this is not correct.
[edit] Find out more
[edit] Related articles on Designing Buildings Wiki
- Bluetooth.
- CAT5.
- Ethernet
- Extranet
- Glossary of electrical terms.
- ICT and Automation (ICTA) Scoping Study Report.
- In-building wireless.
- Information and communications technology.
- Internet of things.
- Internet of things in commercial buildings.
- Local area network.
- Smart buildings.
- Smart cities.
- Smart technology.
- The future of electricity in domestic buildings.
- WiMax.
- WiredScore.
- ZigBee.
[edit] External references
- [80] E. G. Villegas, E. López-Aguilera, R. Vidal and J. Paradells. Effect of adjacent-channel interference in IEEE 802.11 WLANs. Cognitive Radio Oriented Wireless Networks and Communications, Orlando, 2007.
- [81] Butler J. Wireless Networking in the Developing World, Copenhagen: Creative Commons, 2013.
- [82] Institute of Electrical and Electronics Engineering, Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications. IEEE Standards, 2012.
Featured articles and news
The challenge as PFI agreements come to an end
How construction deals with inherit assets built under long-term contracts.
Skills plan for engineering and building services
Comprehensive industry report highlights persistent skills challenges across the sector.
Choosing the right design team for a D&B Contract
An architect explains the nature and needs of working within this common procurement route.
Statement from the Interim Chief Construction Advisor
Thouria Istephan; Architect and inquiry panel member outlines ongoing work, priorities and next steps.
The 2025 draft NPPF in brief with indicative responses
Local verses National and suitable verses sustainable: Consultation open for just over one week.
Increased vigilance on VAT Domestic Reverse Charge
HMRC bearing down with increasing force on construction consultant says.
Call for greater recognition of professional standards
Chartered bodies representing more than 1.5 million individuals have written to the UK Government.
Cutting carbon, cost and risk in estate management
Lessons from Cardiff Met’s “Halve the Half” initiative.
Inspiring the next generation to fulfil an electrified future
Technical Manager at ECA on the importance of engagement between industry and education.
Repairing historic stone and slate roofs
The need for a code of practice and technical advice note.
Environmental compliance; a checklist for 2026
Legislative changes, policy shifts, phased rollouts, and compliance updates to be aware of.
UKCW London to tackle sector’s most pressing issues
AI and skills development, ecology and the environment, policy and planning and more.
Managing building safety risks
Across an existing residential portfolio; a client's perspective.
ECA support for Gate Safe’s Safe School Gates Campaign.
Core construction skills explained
Preparing for a career in construction.
Retrofitting for resilience with the Leicester Resilience Hub
Community-serving facilities, enhanced as support and essential services for climate-related disruptions.
Comments
WiFi does not stand for Wireless Fidelity. It is not an acronym. It is a term to define the ieee 802.11 standard.
WiFi was coined by the Wi-Fi Alliance as shorthand for wireless local area network (WLAN) products based on the Institute of Electrical and Electronics Engineers' (IEEE) 802.11 standards. It did not specifically 'stand for' anything. It has popularly been adopted to mean Wireless Fidelity but this is not correct.